Cylindrical roller bearing manufacturing factory with jnsnbearing.com
High quality cylindrical roller manufacturer: HK, and HK-RS Series - Drawn cup needle roller bearing, Open ends for through shafts, cage guided, with/without seals, Metric dimensional. HF Series--It is made of pressed outer ring and plastic holder; the holder can be installed with plastic reed or the stainless steel reed to guide the needle rollers, bevel race way and needle rollers can be treated as locking device. BCE and BCE-P Series - Drawn cup needle roller bearing, One end closed for shaft ends, cage guided, with/without seals, Inch dimensional NJ Series - Are single row cylindrical roller bearings and have two fixed ribs on the outer ring and a fixed rib on the inner ring which can guide the shaft in a single direction (axially). NUP Series - Are single row bearing roller cylindrical and have two fixed ribs on the outer ring and, on the inner ring, a fixed rib and a support washer. This way they can be used as locating bearings, guiding the shaft axially in both directions. RNU Series - Are single row cylindrical roller bearings and have two fixed ribs on the outer ring and has no inner ring. Instead, it uses the shaft as the opposing raceway. Discover extra information on cylindrical roller bearing manufacturers.
The correct form and dimensional accuracy of outer ring of drawn cup needle roller bearing is achieved only by press fitting into proper housing with appropriate interference. Therefore, roller inscribed circle diameter is measured after press fitted into a standard ring gauge. Full complement drawn cup needle bearings F type has a drawn outer shell that serves as a raceway for the maximum number of rollers. This combines high radial load-carrying capability with low cost. And this series is ideal for applications where the shaft must be removed for service, which is also easy and convenient for assembly. The drawn cup needle roller bearings are commonly used in transmissions, alternators, A/C compressors, pumps, outboard engines, power tools, tractors, door closers etc.
These bearings are separable bearings, and convenient to be mounted and dismounted. They are designed as types of single, double and multiple rows among which the single row cylindrical roller bearings are most applicable. Normally these bearings can accommodate radial load only, none but single row bearings with ribs both on inner and outer rings can carry lighter constant axial load. Application - They are mainly used in large and medium-sized motors, rolling stock, machine tool spindles, internal combustion engines, generators, gas turbines, gearboxes, rolling mills, vibrating screens, lifting and transport machinery, etc. Cylindrical roller bearings are the right choice for high speeds and heavy radial loads. They are produced in different inner ring designs for easy dismounting.
Bearings can be seen everywhere in our lives and work, such as household appliances, garden tools and transportation. For different application scenarios, different bearings assume different roles. The bearings commonly used in vehicles represented by motorcycles and automobiles are starter motor bearings, crankshaft bearings, gearbox bearings and wheel hub bearings. According to the operating conditions of the starter motor, specific requirements are put forward for the bearing's ability to withstand intermittent impact loads, and at the same time, it must have good dust-proof performance and select a reasonable internal bearing clearance. Find more details at https://www.jnsnbearing.com/.
F6000 series bearings are very similar to normal grooved ball bearings, and the only difference is that this type ball bearings have a flange on the outer ring, which can be very useful for mounting the bearings in through holes or axial location. Flanged deep groove ball bearings F6000 series are available in open, shielded and sealed options. The shields and sealed options provide protection to prevent debris and dust getting into the bearing, while at the same time retaining the grease to ensure good lubrication and a long service life. Metric sized deep groove radial flanged ball bearings can bear heavy radial loads and moderate thrust loads in both directions. These bearings are made to the same sizes as standard bearings 6000 series. They also have a flange, which allows flush fitting into housings up to the flange shoulder. This type of bearing is often used on steel tracks to act as both a guide and a support. Deep groove ball bearings are widely used bearings. They use uninterrupted raceways, making them an excellent choice for radial loads. This design achieves precise tolerances even at high speeds.
JNSN Bearing supplier, manufacturer is specialized in producing different types of bearings, sunch as deep groove ball bearings, self-aligning ball bearings, spherical roller bearings, single row tapered roller bearings, inch tapered bearings, automotive bearings, bearing joints, etc. The annual production capability is more than 960 million units. We have solid teamwork and systematic management to offer one-stop service. We’ll monitor every steps during production, then deliver order timely, and the client just need to wait to receive the items. We’re always here ready to listen to client’s needs and provide economical solutions, suggestions or other helps for the client.
Deep Groove Ball Bearings (DGBB) are the most common form of rolling bearings and are used in a variety of applications; particularly those where high speeds and low power loss are required. DGBB can handle not only radial forces, but also moderate axial loads in both directions. They are easy to install and can be deployed in a variety of configurations. Our deep groove ball bearings deliver reliable performance in a wide range of applications and conditions. With super-finished raceways and controlled geometries, our premium design helps ensure consistent quality. Our portfolio includes standard, thin section, narrow, wide and miniature and extra-small deep groove ball bearings that span 3 mm to 400 mm bore sizes. Also there’re several different material options for the bearings, such as chrome steel, stainless steel, hybrid ceramic and etc. The extended product line includes a complete offering of open, shields, seals and snap ring combinations.
The diversity of thin wall ball bearings makes them suitable for a wide range of applications, such as aerospace, semiconductor processing equipment, robotics, medical equipment and other fields. F6700 series is a deep groove ball bearing with a flange on one side of the outer ring. When using this bearing, it is not necessary to provide a step on the inner bore of the housing, so it is possible to process the through hole with high accuracy. Since this bearing is attached to the end face of the housing as a standard, it is necessary to machine the right angle of the housing end face with high accuracy. Single-row flanged deep groove ball bearings F6700 series are available in open and sealed designs. They are designed for high to very high speeds and can accommodate radial as well as axial forces. Flanged bearings are recommended when housing designs cannot accommodate full bearing width, or where the quality of the housing bore is a concern. Moreover, because of their simple design, low operating temperature, and low friction, flanged deep groove ball bearings have a longer expected shelf life than other bearings. They do not require additional lubrication after installation, which also means less maintenance downtime.